THINK SAFETY
PROPER SURFACE PREPARATION & APPLICATION
IS THE KEY TO SUCCESS
INDUSTRIAL SURFACE SOLUTIONS and our MANUFACTURES are committed to public safety and the successful completion of your projects. If you have any product questions, surface preparation, or the proper application of our Specialized Industrial Surface Sealers & Coatings, Please Contact Us!
WE ONLY RECOMMEND USING OSHA APPROVED SAFETY EQUIPMENT
INDUSTRIAL SURFACE SOLUTIONS primary roll is to distribute our specialized industrial surface coatings for the manufacture and into the hands of qualified technicians to ensure the application processes are preformed correctly. Our specialized industrial surface coatings are extremely durable, offer the highest levels of surface protection compared to an other products on the market today. We strongly recommend you reach out and consult with us directly prior to the application of our specialized industrial surface coatings. We are here to support the successful completion of your project.
Services
Consulting
Government agencies, education institutions, businesses, and homeowners.
Services
Staff Training
Industrial Surface Solutions provides training and staff development for your organization.
SURFACE PREPARATION LEADS TO YOUR SUCCESSFUL RESTORATION
SURFACE PREPARATION
STEP 1: STRIP & CLEAN
-
REMOVE ALL DEBRIS
-
REMOVE ALL SILICON COATINGS
-
REMOVE ALL GREASE STAINS
-
REMOVE ALL MOLD OR MILDEW STAINS
-
REMOVE ALL STAINS
* The final finish of your project will reflect the attention to detail of your cleaning and or stripping of the surface prior to the application of our specialized industrial sealers and or coatings. Our products are invisible, clear gloss, clear satin, or clear matte finishes, they do not hide defects.
SURFACE PREPARATION
STEP 2: RINSE & DRY
-
RINSE AND DRY ALL SURFACES AFTER CLEANING OR STRIPPING
-
IT’S IMPORTANT TO REMOVE ALL SEDIMENTS & CHEMICALS
-
WIPE ALL SURFACES WITH CLOTH TOWELS
-
HEAT AND AIR FLOW WILL REDUCE DRYING TIMES
-
RINSE AND DRY
* It’s important to rinse and dry all surfaces once stripped or cleaned prior to the application of our specialized industrial sealers and or coatings. Concrete must have less than 13% moister content prior to application of our sealers or coatings, all surfaces must be completely dry prior to the application of our specialized sealers and or coatings. Coating failure will occur if you apply or products on a wet surface, all surfaces must be dry.
SURFACE PREPARATION
STEP 3: PATCH AND REPAIR
-
AFTER PROPER DRYING IT’S TIME TO ADDRESS DEFECTS
-
MASK OFF OR COVER AREAS NOT TO BE SEALED OR COATED
-
WEAR BOOT OR SHOE COVERINGS TO ELIMINATE FOOT PRINTS
-
IN THIS EXAMPLE GROUTING WAS REQUIRED TO LOOK NEW
-
WIPE ALL SURFACES CLEAN AFTER PATCHING OR REPAIRS
-
KEEP SURFACES CLEAN PRIOR TO APPLICATION
* The final finish of your project will reflect the attention to detail of your patching or repairs of the surface prior to the application of our specialized industrial sealers and or coatings. Our products are invisible, clear gloss, clear satin, or clear matte finishes, they do not hide defects.
SURFACE PREPARATION
STEP 4: REVIEW AND INSPECT FOR FLAWS PRIOR TO APPLICATION
-
REVIEW YOUR PREPARATION OF SURFACES
-
IF YOU SEE FLAWS ON YOUR SURFACE, FIX THEM NOW
-
THE BETTER THE PREPARATION, THE BETTER THE FINISH
-
DO NOT WAIT TO FIX YOUR FLAWS AFTER SEALING OR COATING
-
OUR PRODUCTS WILL NOT COVER YOUR EXISTING FLAWS
* The final finish of your project will reflect the attention to detail of your patching and repairing of the surface prior to the application of our specialized industrial sealers and or coatings. Our products are invisible, clear gloss, clear satin, or clear matte finishes, they do not hide defects.
SURFACE APPLICATION ON TILE FLOOR
STEP 5: APPLICATION - IN THIS EXAMPLE - WE APPLIED - PREMERA T2 SS ANTI-MICROBIAL
-
MIX WELL BEFORE AND DURING USE
-
MIX ANTI-MICROBIAL ADDITIVE
-
MAKE SURE YOU SCRAPE THE BOTTOM OF CAN, USING A STICK, SILVER AND SATIN OR MATTE ADITIVES WILL RELEASE
-
POUR MIXURE INTO AN ACETONE RATED SPRAYER
-
TEST YOUR SPRAY PATTERN ON CARBOARD, CHECK FOR LEAKS
-
IN A CIRCULAR MOTION APPLY MIXTURE TO THE SURFACE, YOU DO NOT WANT TO PUDDLE THE SURFACE YOU ARE APPLYING
-
IDEAL SPREAD RATE IS 2.5 MIL, DO NOT OVER COAT
-
YOU DO NOT WANT INTURUPTIONS DURING PROCESS
-
WORK BACKWARDS FROM YOUR STARTING POINT, YOU DO NOT WANT TO WALK ON A FRESHLY COATED SURFACE
-
AS SOON AS YOU HAVE COMPLETED APPLICATION YOU SHOULD IMIDEATELY CLEAN YOUR EQUIPMENT WITH ACETONE
-
OUR PRODUCTS WILL NOT COVER YOUR EXISTING FLAWS
* The final finish of your project will reflect the attention to detail of your cleaning, patching, repairing, and or preparation of the surface prior to the application of our specialized industrial sealers and or coatings. Our products are invisible, clear gloss, clear satin, or clear matte finishes, they do not hide defects.
